Genie at INTERMAT 2018

Showcasing the brand’s latest eco-friendly and Genie ® Xtra Capacity™ models, Genie Lift Guard™ operator protection systems and the Genie Lift Power™ generator

Advertisement

Focusing on rising market demand for clean, quiet, low and emissions-free access solutions, as well as machines that offer the ability to lift heavier loads, Genie, a Terex brand, will be showcasing nine of its latest and best-selling products at Intermat 2018, to be held from 23rd to 28th April at Parc des Expositions, Paris- Nord Villepinte on stand number E5 K 025.

Highlights will include the brand’s new generation of environment-friendly hybrid and electric work platforms, new additions to the Genie ® Xtra Capacity™ (XC™) boom lift family and an upgraded model of the electric Genie GS™-4047 scissor lift. The brand will also be showcasing its new Genie Lift Guard™ line of operator protective systems, and new Genie Lift Power™ generator solution.

Genie accessories on show include:

• The new Genie Lift Power™ generator solution that features a dedicated hydraulic circuit, a right-sized breaker and no pressure switch to run the unit reliably, and allows the power to lift and drive during operation. The 3kW Genie Lift Power system is available on Genie XC telescopic boom lifts and is convertible from the European 230/50 power system to the 115/50 UK system at the click of a switch.

New Genie Lift Guard™ operator protective systems

• The Genie Lift Guard™ Contact Alarm system is an electronic secondary guarding system, that in some circumstances can provide additional operator protection. Designed to immediately activate and alert ground personnel if an operator makes contact with the breakaway cable by means of a sound alarm and a flashing beacon, the Genie Lift Guard Contact Alarm system is now compatible with 2.4 m (8 ft) auxiliary top rails and new control box protection accessories. Installed standard from the factory on most new Genie articulated and telescopic boom lifts, it is also available as an aftermarket kit which can easily be retrofitted in less than 30 minutes with only a few fasteners and electrical harness connectors on units back to 2003.

• The Genie Fall Arrest Bar. Because there can be times when a worker need to perform their necessary tasks from a structure adjacent to the platform, this new system enables the worker to use their Genie® boom lifts as a fall arrest anchor to enjoy the benefit of a greater working area to move around in, while remaining connected to the platform.

Other products on display will include the Genie GTH™-2506 compact telehandler and popular Genie AWP™ personal lift and Genie® SLA™ materials lift.

More information on the Genie SX-135 XC, S-85 XC, S-65 XC and Z-45 XC booms

To adapt to today’s widespread need to enable people to work at height safely with increasingly heavy loads using a single machine, all models of the expanding Genie telescopic and articulating XC family feature a consistent dual lift capacity of 300 kg (660 lb) unrestricted and 454 kg (1,000 lb) restricted across the entire working envelope. These models also provide customers the ability to work with up to three people onboard while still leaving room for tools and jobsite materials.

The Genie XC boom family currently counts eight models: SX-135 XC, SX-125 XC, SX-105 XC, S-80 XC, S-85 XC, S-60 XC, S-65 XC and Z-45 XC booms.

Telescopic Genie S and SX booms offer maximum platforms heights from 19.79 m (58 ft 4 in) to 41.15 m (135 ft ). Unique features include:

• New Automatic Envelope Control Technology providing the ability of retracting the boom automatically when it reaches its operating envelope. Allowing for simple platform positioning and an enhanced operator experience, the system’s low maintenance load-sensor cell continuously checks the weight in the platform in real-time to limit the operating envelope to match the load chart.

• Zero-Load Calibration increases productivity and reliability by means of the load sensor cell that continuously weighs the load in the platform. As a result, calibration in the field no longer requires burdensome test weights. Full-factory calibration only needs to be performed during annual inspections. Operators will find the control layouts to be consistent and intuitive, making machine operation even more straightforward than before. Designed to meet the overload restriction guidelines in the current European EN280 standard, this new system monitors the weight in the platform and disables drive, steer and certain boom functions if the load exceeds the platform load limit.

• For Genie SX XC models, a new mini Genie XChassis™ axle design combines excellent stability, a compact 3.94 m (12 ft 11 in) x 4.11 m (13 ft 6 in) footprint, with axles that extend and retract to and from the stowed position 2.49 m (8 ft 2 in) retracted or 3.94 m (12 ft 11 in) extended and a narrow profile for transport on a standard low-bed trailer.

New to the European market, the Genie S-65 XC boom will be available in EMEAR in Q3, 2018.

The articulating Genie Z-45 XC model offers an horizontal reach of 7.54 m (24 ft 8 in) to a maximum up-an- over clearance of 7.22 m (23 ft 8 in). Unique features include:

• A simple calibration process to improve productivity by providing the ability to set up the primary boom, secondary boom and jib bell crank faster.

• Larger reinforced rotator support, a wider jib and re-designed cylinders to adapt to its increased lift capacity.

• A new improved load sense system to increase performance, decrease calibration time and improve overall productivity. Drive-enabled at full height under maximum load, these models also features the brand’s unique full-time, positive drive traction and active oscillating axle system.

Genie Z-60/37 FE hybrid articulating boom lift – ERA Rental Product of the Year

The Genie Z-60/37 FE boom is the first and only true high performance hybrid unit on the market to combine the power and performance of 4WD diesel machines, with the quiet, clean efficiency of electric powered units. The Genie Z-60/37 FE boom lift features two modes of operation that are interchangeable at the click of a switch. In ‘All-Electric’ mode, it can provide a full shift of operation on a single battery charge. Used in ‘Hybrid’ mode, it provides more than a week of run time with a single tank of diesel to perform extremely efficiently in rough terrain conditions. In hybrid mode, the machine uses its environmentally friendly Stage IIIB/Tier 4F engine-powered generator to maintain the state of charge of the batteries. As a true hybrid machine, when braking or descending inclines, the Genie Z-60/37 FE boom lift uses regenerative braking to recover energy that is in turn used to recharge its batteries.

With its two modes of operation, the Z-60/37 FE boom offers rental companies a versatile, sustainable and powerful ‘two-in- one’ solution adapted to indoor as well as outdoor applications, even where on-site electric power is not available. It also offers the advantage of economising between 15 to 30 Euros of fuel a week, and the ability to run more than eight hours on a full overnight battery charge.

Genie Z-33/18 electric articulating boom lift

Offering excellent rental returns on invested capital (rROIC) at the entry level of the electric Genie articulating boom lift range, the 12 m (39 ft 4 in) Genie Z-33/18 boom is a simple, robust electric unit powered by an efficient three-phase AC electric drive system. Requiring less energy and offering longer battery cycles, in addition to the benefits of quiet, zero emissions performance and ease of operation, this machine is able to drive longer distances, needs to be recharged less often and costs less to maintain than units equipped with a DC transmission.

Added to its broad field of application, the Genie Z-33/18 lift provides the ability to perform a full day’s work — both indoors and out — on a single battery charge. Significantly lighter than traditional machines in the 12 m (39 ft 4 in) category, the Genie Z-33/18 lift weighs just 3,665 kg (8,025 lb) — which is nearly 1,500 kg (3,306 lb) less than other types of electric-powered unit. This model notably boasts a total occupied floor pressure of only 991 kg/sq m and a low tyre contact pressure of 483 kPa which make it an ideal solution for applications on fragile indoor surfaces where reduced floor load is paramount, as well as outside duties – even on wet grass or freshly stabilised ground.

Updated Genie GS-4047 self-propelled electric slab scissor lift

Built for indoor tasks, the Genie GS-4047 self-propelled electric scissor lift is purpose-built to meet the demands of tightly packed, high-rise indoor spaces found in modern tilt-up warehouse construction. This scissor lift lifts to 350 kg (770 lb) to a maximum working height of 13.70 m (44ft 11 in) and drives at full height. A 48 V battery pack offers plenty of power for getting around jobsites and operating a full day of work. Designed with dual front-wheel drive and a zero inside turning radius, combined with a compact footprint of just 2.43 m (8 ft) long and 1.19 m (47 in) wide stowed for work in tight access areas. A 0.91 m (3 ft) extension deck allows workers and tools to maximize the platform workspace.

Upgraded Genie SmartLink™ Control System

Allows for improved on-board diagnostics and troubleshooting with easy-to- read and user- friendly machine adjustments, the Genie GS-4047 scissor lift incorporates the updated Genie SmartLink™ control system, offering operators fully proportional lift and drive for precise positioning.

Upgraded Genie Smart Charger™ system for electric slab scissor lifts

Provided as standard on all all new generation Genie slab scissors, the Genie GS-4047 scissor lift now features an upgraded onboard Genie Smart Charger™ system that adds several significant improvements to the charging system, including recharging batteries is 20 percent faster than on earlier models, two windows — one on the side of the machine plus one at the back with the power source, battery state of charge is easier to visualise and access and time spent moving machines is significantly reduced. Other improvements include LED lights that indicate the evolution of the charging cycle. During recharging, the LEDs flash green. When the battery reaches full charge, the screen ceases flashing and a solid green screen shows that the machine is fully charged. Additionally, if a fault occurs during the process, it is signalled by an orange screen that means that anomalies do not go unnoticed and delays are avoided. Thanks to the USB port on the Genie Smart Charger system, it is also possible to access information on previous battery charges directly on a laptop computer or smartphone via the Genie SmartLink troubleshooting and diagnostics system.